JSC Additive Technologies Center was established in 2018 based on holding companies of ROSTEC Aviation cluster to be the main integrator of additive manufacturing.
The organization's stockholders are JSC "United Engine Corporation", JSC "Technodinamika", JSC "Concern Radio-Electronic Technologies" and JSC "Russian Helicopters".
Our mission is to become the leading integrator of complex solutions in additive manufacturing for Russian industry.
JSC ATC has the largest fleet of industrial equipment in Russia (3D printers, measuring machines, machining and laboratory equipment) and a team of technical specialists with considerable experience in the implementation and use of additive technologies. This allows us to solve problems of any complexity.
According to experts, additive technologies can increase labor productivity by 30 times, bring the material utilization factor (CMM) to 98%, and reduce the weight of the structure by 50%.
The duration of the cycle from the drawing to the product is reduced to a minimum, operating and capital costs are sharply reduced, the environmental safety of all technological conversions increases.
Parts created by us, in terms of their mechanical behavior, density, residual stress and other properties, surpass analogs obtained by casting or machining.
Thanks to additive technologies, it became possible to produce a large number of such parts without the use of equipment and in the shortest possible time.
Additive technologies are actively used in mechanical engineering, industry, science, education, design, medicine, foundry and many other areas.
As a result of the use of additive technologies, the time and cost of production has been significantly reduced by reducing the number of operations, transitions and the absence of the need for the manufacture of special equipment.
Materials: :
AlSi10Mg
Build volume::
500х500х500 mm
DMP Factory 500 (DMP Technology)
Building area 500x500x500 mm - using powders of aluminum alloy AlSi10Mg.
Materials: :
stainless steel 316L, EP648
Build volume::
225x225x280 мм
Concept Laser M2 (SLM)
Build volume is 225x225x280 mm, printing by 316L stainless steel powder and nickel EP648 alloy of domestic production.
Materials: :
Ti6Al4V, heat-Resistant Nickel alloys
Build volume::
1000х800х650 мм
InssTek MX-1000 (DMT)
Build volume is 1000х800х650 mm, printing by Ti 6Al 4V powders and Nickel based alloys
Materials: :
AlSi10Mg, Ti6Al4V
Build volume::
275х275х420 мм
3D Systems ProX DMP 320 (SLM)
Build volume is 275х275х420 mm, printing by AlSi10Mg aluminum alloy powder, Ti6Al4V titanium alloy powder is planned to be used
Materials: :
CoCr, Stainless steel
Build volume::
400х400х400 мм
EOS M400-4 (SLM)
Build volume is 400х400х400 mm, printing by CoCr alloy;
Materials: :
CoCr
Build volume::
250х250х325 мм
EOS M290 (SLM)
Build volume is 250х250х325 mm, printing by CoCr alloy;
7, Vishnevaya str, Moscow
Phone: 8-495-197-76-50
E-mail: sale@rt-3d.ru
Our mission is to become the leading integrator of complex solutions in additive manufacturing for Russian industry.
- To reduce the time needed to bring new high-tech products to the market
- To change the approach to designing and production of innovative products
- To reduce Russia's lag behind foreign companies in implementing additive technologies in industry
- The customer is always right. The customer is the main source of our well-being and development, which requires respect.
- СModernity: always keep up with the times and one step ahead, using modern production technologies and management methods.
- The quality of our products and services must meet consumers’ requirements and exceed their expectations.
- To maintain existing and develop new markets for products and services.
- To develop and bring to market the types of products and services required by the consumer.
- To improve the quality of products and services basing on consumers’ requirements and expectations.
- To preserve the workforce and maintain a favorable psychological climate that contributes to the identification of problems and their effective solution.
- Improving the effectiveness of the organization's activities and its competitiveness, taking into account the interests of customers, shareholders of the company and the team.
- Systematic analysis of current and future consumers’ requirements and expectations and their meeting with our products and services.
- Meeting the requirements and continuously improving the effectiveness of the quality management system based on the international standard ISO 9001.
- Regular training and improvement of staff competence.
- Development of new and improvement of existing production technologies.
- Development of the organization’s material and technical base - the acquisition of new equipment.
- Creating mutually beneficial relationships with suppliers based on trust and partnership.
The management of JSC ATC assumes responsibility for the implementation of this quality policy, for ensuring that it is understood and supported by all employees of the company.
V. O. Kochkurov